Skip to content

We let energy flow.

Energy means performance

Plants need electrical energy without disturbances and interruptions. In order to ensure safe plant operation, our employees perform outstandingly. From planning and construction to maintenance and servicing, they ensure that plants can be operated at full power. We are therefore pleased that our employees enjoy an excellent reputation and are among the best in our industry.

I&C

Power engineering

MV systems, LV systems or standby power systems. Our services in the area of power engineering comprise all the essential process steps and work steps from projection and detail planning, the necessary installation, connection technology and wiring up to commissioning and documentation.

  • MV switchgear systems, air-insulated and gas-insulated
  • Distribution, block and machine transformers in oil, hermetically sealed and resin potted versions
  • Supply service points in prefabricated design
  • Room equipment, double floors
  • Protection methods, control technology and telecontrol
  • Network calculations; short-circuit calculation, load flow calculation, engine start-up analysis, selectivity studies
  • Projection and detail planning
  • All the necessary installation, connection technology, cabling
  • Commissioning and documentation
  •  
  • Low voltage switchgear combinations according to EN 61439 Part 1-6 (ICE 61439)
  • Motor Control Centres in draw-out or plug-in technology
  • In-house switch cabinet manufacture
  • Control distributors (SIMATIC, B&R, HIMA, etc.)
  • Frequency converter cabinets
  • Compensation systems
  • Overvoltage protection cabinets
  • Extended power supply and measurement transformers, isolating cabinets etc.
  • Installation and floor distributors
  • Pneumatic distributors, protective boxes for measuring instruments and transmitters
  • Controllers for standby power supplies
  • EDP and network cabinets etc.
  • Protection methods and control technology
  • Busbar systems
  • Room equipment, double floors
  • Projection and detail planning, network calculations,
  • All the necessary installation, connection technology, cabling, cable run construction etc.
  • Commissioning and documentation
  • Uninterrupted power supplies (UPS) static and dynamic
  • Rectifier systems
  • Battery systems
  • Emergency power diesel systems
  • Emergency lighting
  • Projection and detail planning, network calculations,
  • All the necessary installation, connection technology, cabling, cable run construction etc.
  • Commissioning and documentation
kremsmueller-emsr-elektrische-mess-steuer-und-regelungstechnik-01
Kremsmueller-EMSR-automatisierungstechnik

I&C

Automation control engineering

Automation control engineering that is convincing. In our concepts, we combine our versatile know-how of electrical I&C into optimum system solutions. From projection and detail planning with all the concomitant procedures up to installation, commissioning and documentation, we support you in the entire life cycle of your plant.

  • Projection and detail planning
  • Functional and system specification generation
  • Generation and formulation of customer-specific and process-specific concepts
  • Energy management systems for multiple emergency power systems
  • Energy monitoring and measurement value analysis systems (Acron)
  • Application software for PLC / PLS (for example: Simatic, Allen Bradly, etc.)
  • SCADA and visualisation systems with application software Simatic WINCC, WINCC OA, Intouch, Copadata Zenon, Atvise, etc.)
  • Production data acquisition / management, long-term archiving, recipe management, user administration, remote data management etc.
  • Networking of plant control, client/server solutions
  • Telecontrol systems and teleservice of electric systems
  • All the necessary installation, connection technology, cabling, cable run construction etc.
  • Commissioning and documentation

I&C

I&C industrial plant engineering

I&C engineering for industrial plants has to meet special challenges in the area of safety and performance. Hence, for example, installations in explosion-susceptible areas require a lot of experience and solid know-how, from projection and detail planning up to installation, commissioning and inspection.

  • Projection and detail planning
  • Installation in explosion-endangered zone (Ex-zone)
  • I&C industrial plant installation
  • Power supplies and controllers in accordance with the requirements
  • Control distributors (SIMATIC, B&R, HIMA, etc.)
  • Pneumatic distributors, protective boxes for measuring instruments and transmitters
  • Gas warning systems, measurement techniques
  • Analysis and process piping
  • Process instrumentation
  • Earthing, equipotential bonding and lightning protection
  • Overvoltage protection
  • Trace heating, electric heating
  • Generation and editing of electric systems documentation such as circuit diagrams, construction plans, as-built documentation, terminal plans, cable lists (for example: ELCAD, E-PLAN, AUTOCAD, COMOS, Promis, etc.)
  • Explosion circuit calculations according to EN 60 079-14/25
  • SIL circuit calculations EN61508 and EN61511
  • Operating equipment design for explosion-endangered zones
  • Commissioning, loop check, support for process technology
  • Initial inspection in accordance with EN 8001-6-61, asset ledger
  • Plant inspections, findings
Kremsmueller-EMSR-industrieanlagentechnik
Kremsmueller-EMSR-gebaeudeausruestung

I&C

Building equipment

Industrial and production plants, administrative centres or traffic installations. They are all characterised by higher levels of technology and availability as well as marked customer-specific requirements. We are able to surmount all these challenges because we supply the projection, detail planning, installation, documentation and testing of building equipment from a single source.

  • Projection and detail planning according to customer specifications and requirements specifications for industrial and production plants, administration centres, traffic systems and other systems with high technology and availability.
  • Power supplies and controllers in accordance with the detailing given below
  • Emergency lighting
  • Fire alarm systems
  • Access control and safety systems
  • EDP and network technology
  • Subsurface systems
  • Cable run technology
  • Function-retaining cable systems
  • Energy, installation and control wiring
  • Electro-acoustic systems (sound)
  • Video and camera systems
  • Gas warning systems
  • Optical fibre technology (single-mode, multimode)
  • Vehicle charging stations
  • Lighting systems for indoors and outdoors
  • Street lighting and tunnel lighting
  • Analysis and process piping
  • Process instrumentation
  • Earthing, equipotential bonding and lightning protection
  • Installation in explosion-endangered zone (Ex-zone)
  • Trace heating, electric heating
  • PV systems
  • Constructive steel structures
  • Calibration
  • Generation and editing of electric systems documentation such as circuit diagrams, construction plans, as-built documentation, terminal plans, cable lists (for example: ELCAD, E-PLAN, AUTOCAD, COMOS, Promis, etc.)
  • Light calculations, cable calculations, routing etc.
  • Initial inspection in accordance with EN 8001-6-61, asset ledger
  • Plant inspections, findings
  • Support for acceptance by public authorities, electrical engineering

I&C

Upkeep, Maintenance and After-Sales-Service

Clearly defined maintenance processes as well as services, and regular inspections and maintenance procedures are of decisive importance for fault-free operation of plants. If technical faults occur nonetheless, we are your reliable partners for fast and sustainable rectification of problems.

  • Maintenance strategies, maintenance sequences
  • Initial inspections, asset ledger E 8001-6-61, E 8001-6-63
  • Recurring inspections in accordance with EN 8001-6-62 and EN 60079-17
  • Fault rectification, on-call service
  • Cyclical maintenance, calibration and service
  • Damage analysis and rectification
  • Working out the performance scope for simplified flow control
  • Lockout-tagout systems (for increased safety)
  • Spare parts storage, spare parts management,
  • Standardisation
  • Thermography
District cooling powers the Vienna General Hospital (AKH) and Ö3 radio

District cooling powers the Vienna General Hospital (AKH) and Ö3 radio

The environmental balance is also outstanding.
Read more

Our EMSR team at the Donaustadt power plant

A MAJOR PROJECT FOR THE EMSR IN SCHWECHAT
Read more
Sheet rolling mill

Greater Quality and Efficiency Thanks to New Control Station

Kremsmüller fulfilled all customer requirements when converting the sheet rolling mill for Böhler Bleche
Read more

Contact person

Your contact for EMSR - Electrical Measurement and Control Technology.